Free display tests that run in your browser. Nothing is uploaded.

Input and geometry

Mouse polling rate test

How many times a second your mouse, trackpad or stylus actually reports to the browser, measured from the samples themselves.

Move the pointer in here

Measured rate
—
Snapped to standard
—
Peak this session
—
Median interval
—
Samples in window
—
The window is the last second of movement.

How to run this test

  1. Move the pointer around inside the pad below, in wide continuous sweeps rather than short flicks.
  2. Keep moving for a few seconds. The reading is a rolling median over the last second, so it settles as samples arrive.
  3. Read the snapped figure. It is the standard rate your measurement is closest to, and it is blank when nothing is close enough to claim.
  4. Press Reset and sweep again to confirm. A rate that changes between runs usually means the pointer left the pad or the system throttled it.
  5. Compare with the rate set in your mouse software. A 1000 Hz mouse reading 125 Hz is usually a driver or USB port problem, not a faulty mouse.

What a problem looks like

The reading sits at your refresh rate
A figure suspiciously close to 60, 120 or 144 means the samples are arriving one per frame rather than one per report. The page says so explicitly when your browser has no coalesced-event support. If it does have support and you still see this, something between the device and the browser is batching, most often a remote-desktop session or a virtual machine.
A high-end mouse reads 125 Hz
That is the USB default many systems fall back to. Check the rate in the manufacturer software, try a different port, prefer a direct port over a hub, and check whether a wireless receiver is set to a lower rate than the mouse itself.
The number jumps around
Sampling is not perfectly even, so a rolling median moves a little. Large swings usually mean slow, hesitant movement: with few reports per second there is not much to take a median of. Sweep faster and wider.
A trackpad reads far lower than a mouse
Trackpads and touchscreens generally report more slowly than gaming mice, and many throttle further on battery. That is the device behaving normally rather than a fault.

What to do next

If the rate is lower than your device is set to, check the manufacturer software first, then the USB port, then the receiver. If it matches, there is nothing to fix here: polling rate is a property of the device and its driver, not of the screen.

Questions people actually ask

Why can a web page measure this at all?

Because pointer events carry the samples the operating system delivered, not just the one the browser had time to dispatch. A pointermove event fires at most once per frame, but getCoalescedEvents on that event returns every intermediate sample with its own timestamp. Timing those gives the real report rate.

Is this as accurate as a dedicated polling rate tool?

It is close for the rates most people have. Desktop tools read the USB stream directly, which avoids the browser entirely. Here the timestamps pass through the event system, so the median is reliable while individual intervals are noisier. At very high rates, 4000 Hz and above, treat the figure as indicative rather than exact.

What does the snapped value mean?

The measured figure is matched against the standard rates devices actually use: 125, 250, 500, 1000, 2000, 4000, 8000 Hz. If your reading is within 12 per cent of one of those, it is shown as the snapped rate. If it is not close to any of them, the field stays empty rather than rounding you to a number your device does not use.

Does a higher polling rate make a difference?

It lowers the delay between moving your hand and the system knowing about it, by a few milliseconds between 125 and 1000 Hz. Above 1000 Hz the returns shrink quickly and the extra reports cost CPU time. Whether you notice is a question about you, not about the hardware, and nothing on this page can answer it.

Can I test a stylus or a touchscreen with this?

Yes. Pointer events cover mouse, pen and touch in one path, so drag a finger or a stylus across the pad and the same measurement applies. The touch screen test is the better page if you want multi-touch tracking and drift instead of a rate.