By device
Gaming monitor test
A gaming monitor is bought for motion, so motion is where the run starts. Measure what you are actually getting first, then tune the settings that change it.
Last updated
Before you start
- Set the monitor to its highest refresh rate in the operating system display settings. Plugging it in does not do this for you, and a 240 Hz panel running at 60 Hz is the most common disappointment there is.
- Use the cable that came with it, plugged directly in. Adapters, hubs and long cheap cables are where refresh rate and colour depth quietly get negotiated down.
- Turn off any motion blur reduction or backlight strobing for now. It interacts with everything else and belongs at the end of the run, not the start.
- Note your current overdrive setting before you change anything, so you can get back to it.
- Give the panel twenty minutes to warm up. Liquid crystal is slower when cold and a VA panel in a cool room will look worse than it really is.
The run, in order
- 01 Refresh rate test
Confirm you are actually getting the rate you set. This is a median of several hundred frame intervals, so one stall cannot flatter or ruin it, and it is the number everything else depends on.
- 02 Frame skipping test
A high rate that is being accepted but not presented is worse than a lower rate that works. This is the pattern you photograph to find out, and it takes two minutes.
- 03 Screen tearing test
A hard moving edge. Tearing here means your compositor and display are out of step, which affects everything and not only games.
- 04 Ghosting test
The overdrive tuning page. Run the moving objects at several speeds and find the setting with the shortest trail and no bright halo in front.
- 05 Response time test
Transitions across several level pairs, to check the setting you just chose holds up on colour and mid-tone changes rather than only on black to white.
- 06 Black smearing test
If the panel is VA, this is where it will struggle. Dark-to-dark transitions are the slowest and the ones that matter in a night-time scene.
- 07 Frame rate test
Live frame pacing with the one per cent low. Stutter with a good average is a different problem from a low average, and this separates them.
- 08 Mouse polling rate test
The other half of the input chain. A 1000 Hz mouse that is reporting at 125 Hz undoes a lot of what a fast panel is doing for you.
What matters on this hardware
The rate you set versus the rate you get
Operating systems do not raise the refresh rate for you when you plug in a new monitor. Set it explicitly, then measure it. This is the single most common gap between what people paid for and what they are using.
Overdrive overshoot
The strongest overdrive setting is almost never the best. Past a point it pushes pixels beyond their target and you swap a dark trail for a bright halo, which most people find more distracting.
Variable refresh rate flicker
Some panels flicker in dark scenes when the frame rate swings inside a VRR range, because the panel is being asked to hold frames for varying lengths of time. Capping the frame rate a little below the maximum often helps.
Backlight strobing trade-offs
Motion blur reduction strobes the backlight to shorten the time each frame is held, which genuinely sharpens motion. It also costs brightness, usually cannot run alongside variable refresh rate, and gives some people headaches.
Hold-type blur is not the panel
Most of the blur you see tracking a moving object comes from the frame being held while your eye keeps moving. It improves with refresh rate rather than with response time, which is why a 240 Hz panel looks clearer than a 144 Hz one with the same rating.
Cable and bandwidth limits
High refresh rate at high resolution needs more bandwidth than many cables carry. The symptoms are a rate that will not appear in the settings, a picture that drops out, or colour quietly being subsampled to fit.
Questions people actually ask
What overdrive setting should I use?
The strongest one that shows no bright halo in front of a moving object. Tune it on the ghosting test at the speed you actually play at, not at the fastest available. Settings named Extreme or Fastest overshoot on most panels.
Is 144 Hz enough, or do I need 240?
This site cannot answer that for you, because it is a question about your eyes and what you play. What it can do is show you the difference: run the motion tests at each rate your monitor supports and see whether you can tell them apart. That is a better basis than anyone else’s opinion.
Why does my monitor look blurry in motion despite a 1 ms rating?
Because most motion blur on a sample-and-hold display comes from the frame being held for the whole refresh while your eye moves smoothly across it. That is hold-type blur. It gets better with a higher refresh rate or with backlight strobing, and response time ratings have little to do with it.
Should I turn on variable refresh rate?
Usually yes. It removes tearing without the input lag that vertical sync adds. Watch for flicker in dark scenes on some panels, and consider capping your frame rate slightly below the maximum, which keeps you inside the range where it behaves best.
Does a high polling rate mouse matter?
It lowers the delay between your hand moving and the system knowing, by a few milliseconds between 125 and 1000 Hz. Above 1000 the returns shrink quickly. Whether you notice is personal, and the polling rate test at least tells you what you are actually getting.