PWM flicker test
Fields and a procedure for finding backlight pulsing, which you cannot see directly and can often see the effects of.
Esc to exit · arrow keys change the field · H hides the controls
A neutral field for the camera method. Start here.
The two methods, in order of effort
- Wave something. A pen or your fingers, quickly, ten centimetres from the screen. Separate copies rather than a blur means pulsing.
- Use a phone camera. Manual shutter near 1/1000 second, or slow motion. Rolling dark bands mean pulsing, and wider bands mean a lower frequency.
Neither gives you a number. Both tell you whether it is happening, which is the question that matters if a screen is tiring you.
How to run this test
- Set your display to the brightness you normally use, then to its lowest. Flicker is usually worst at low brightness.
- Press Go full screen on the mid grey field.
- Wave a pen or a finger quickly across the screen, about ten centimetres away. If the backlight is pulsing, you see separate frozen copies of it rather than a smooth blur.
- For a clearer result, point a phone camera at the screen and use a manual shutter speed around 1/1000 second, or slow-motion video. Dark bands rolling through the frame mean pulsing.
- Repeat at each brightness level. A display that shows bands at low brightness and none at high brightness is using PWM only in the lower part of its range.
What a problem looks like
- Separate copies of your hand rather than a blur
- The classic pencil-wave result. The light is switching on and off fast enough that each pulse freezes a different position of your hand. It is the simplest evidence of pulse-width modulation, and it needs no equipment.
- Dark bands rolling through a phone camera view
- The camera sensor reads line by line, so a pulsing light produces banding. Wider, slower bands mean a lower modulation frequency, which is the kind people are most sensitive to. Confirming it is easy; putting a number on it is not.
- Flicker at low brightness only
- Very common. Many displays run the backlight at full power and use PWM only to dim, so the pulses get shorter and more obvious as brightness drops. Raising brightness and lowering contrast is a workaround that helps some people.
- Eye strain with no visible flicker
- Possible and reported by many people. Visible flicker and the strain it causes are not the same threshold, and modulation well above what you can consciously see still reaches your visual system. If a display tires you and you cannot see why, this is a candidate.
- An OLED phone that flickers at every brightness
- Most OLED phones dim by pulsing, often at a few hundred hertz, across the whole range. Some offer a high-frequency dimming or DC dimming option in the display settings. It is worth looking for if screens tire you.
What to do next
If you find pulsing and screens tire you, look for a flicker-free or DC dimming setting, and check independent measurements before buying a replacement. Running higher brightness with lower contrast keeps some displays out of their PWM range.
Questions people actually ask
What is PWM?
Pulse-width modulation. Instead of running the backlight or the emitters at a lower power, the display switches them on and off very quickly and changes how long they stay on. The average light output drops, and the colour stays consistent, which is why it is used. The cost is that the light is pulsing rather than steady.
Why can a web page not measure the frequency?
Because there is no API for backlight modulation, and nothing on the page can see the light your display is emitting. Measuring it means observing the light directly, with a camera at a known shutter speed or a photodiode. Any site that reports a PWM frequency from a browser has invented it.
Is flicker harmful?
It causes headaches, eye strain and general discomfort for some people and not others, and sensitivity varies a lot. There is no agreed threshold, though lower frequencies are more often reported as a problem than higher ones. If screens tire you and this test shows pulsing, it is a lead worth following.
How do I find a display without it?
Look for flicker-free or DC dimming in the specification, and check independent measurements, because marketing claims here are unreliable. On phones, look in the display settings for a high-frequency dimming option. Hardware review sites that measure with a photodiode are the only trustworthy source of frequency figures.
Does the pencil test work on every display?
It works when the pulsing is slow enough and deep enough for your eye to catch. A display modulating at several kilohertz with a shallow duty cycle can pulse without producing visible copies. The camera method catches more, and neither catches everything.